Quick Link
Quick Contact
Address
6 building,No 98, Fulian 1 road,Baoshan district, Shanghai, China.
Tel
86-021-80392549
Our Newsletter
Subscribe to our newsletter for discounts and more.
This IP67 high-pressure water jet industrial robot arm cleaning station is a turnkey washing cell built around the FANUC M-20iD/35 mechanical unit. A 35 kg wrist payload and a 1,831 mm reach let one station carry heavy castings, welded frames and machined housings through rinse, degrease and blow-off without re-fixturing the workpiece.
The high-pressure water jet tooling runs an adjustable 80 to 150 bar fan or needle spray through up to six nozzles, lifting chips, cutting fluid, release agent and burn marks out of blind holes, threaded bosses and ribbed surfaces. Wrist and J3 arm are sealed to IP67, so spray, splash and wash chemistry never reach bearings, motors or cabling; the body retains its IP54 to IP65 rating and an optional stainless splash enclosure keeps overspray inside the cell.
Motion is coordinated by the FANUC R-30iB Plus controller. A washing program is taught once and then repeated at +/-0.03 mm repeatability, so nozzle standoff, impingement angle and dwell time stay identical from the first part to the ten-thousandth. Standard PROFINET, EtherNet/IP and discrete I/O hand the cycle over from the upstream press, machining centre or welding line without custom code.
Every IP67 high-pressure water jet industrial robot arm cleaning station is assembled, pressure tested and run in before shipment. Cycle sheets, nozzle layout drawings, controller backups and a 12 month warranty ship with the unit, and our engineers support program tuning remotely during commissioning so the cell reaches rated output in the first production week.
| Category | Robotic Cleaning Workstation | Robot Type | 6-Axis Articulated |
| Wrist Payload | 35 kg | Maximum Reach | 1,831 mm |
| Repeatability | +/-0.03 mm | Protection | IP67 Wrist & J3 Arm / IP54-IP65 Body |
| Wash Pressure | 80-150 bar, Adjustable | Nozzle Count | Up to 6 Fan or Needle Jets |
| Controller | FANUC R-30iB Plus | Mounting | Floor Mounted Cell |
| Robot Mass | 250 kg | Voltage | 380-415 V / 50-60 Hz |
| Warranty | 12 Months | Primary Application | Workpiece Washing and Degreasing |
Q: What makes this unit a genuine IP67 cleaning station rather than a covered robot?
A: The wrist and J3 arm are sealed to IP67 as delivered, so the joints, motors and cable entry tolerate direct high-pressure water jet spray and repeated washdown. The body keeps its IP54 to IP65 rating, and the cell adds a stainless splash enclosure, floor drainage and mist extraction to keep overspray contained.
Q: Which wash pressure and nozzle set does the high-pressure water jet system use?
A: The pump and manifold are set for an adjustable 80 to 150 bar and drive up to six fan or needle nozzles. Fan jets cover large flat faces quickly, needle jets reach blind holes and threads, and the program switches between them inside a single cycle.
Q: What kind of workpiece can the 35 kg payload handle?
A: Up to 35 kg at the wrist including gripper and fixture. That covers most machined housings, gearbox cases, welded frames and die castings; heavier parts can be supported on a driven positioner while the arm controls the nozzle path.
Q: How consistent is the wash result from part to part?
A: Repeatability is +/-0.03 mm, and the 1,831 mm reach lets the program keep a fixed nozzle standoff across the whole part. Because dwell time and impingement angle are stored in the program, every part receives the same wash energy as the first one.
Q: Can washing and blow-off run in the same cycle?
A: Yes. A typical cycle runs pre-rinse, high-pressure wash, clean rinse and air blow-off, with the arm carrying either the nozzle manifold or the part. Cycle sections are timed and can be trimmed in the controller without re-teaching the path.
Q: What documentation and support are supplied with the station?
A: Each station ships with cycle sheets, nozzle layout drawing, controller backup, electrical and pneumatic schematics, pressure test record and a 12 month warranty. Our engineers support remote program tuning and operator training during commissioning.