Quick Link
Quick Contact
Address
6 building,No 98, Fulian 1 road,Baoshan district, Shanghai, China.
Tel
86-021-80392549
Our Newsletter
Subscribe to our newsletter for discounts and more.
This headlight screw tightening workstation is built around a FANUC CRX-5iA collaborative robot, a torque-controlled screwdriving spindle and a two-position rotary fixture, so automotive lighting assemblies are fastened to the same torque and the same angle on every cycle. The robot arm, driver, feeder and fixture are assembled, wired and tested as one cell before shipment, which means the workstation arrives as a working unit rather than a box of loose parts.
With a 5 kg payload and 994 mm working reach, the cobot covers a full headlight housing plus its mounting brackets without repositioning the fixture. The 6 axis articulated arm reaches into recessed lamp cavities, tilts the driver to the correct approach angle, and keeps +/- 0.03 mm repeatability so screw depth and thread engagement stay inside the tolerance band defined by the lamp supplier. Force sensing is fitted as standard, allowing the screwdriver to seat each fastener with controlled contact force instead of a fixed stroke.
Because the arm is safety rated and force limited, the cell normally runs without a safety fence. Operators load and unload housings from the open side while the cobot works on the opposite station, which suits mixed-model headlight lines where batch sizes are small and changeover has to be quick. Everything is programmed through hand guidance or the teach pendant, so a new lamp variant is taught by leading the arm through the fastening points instead of writing code.
| Parameter | Specification |
|---|---|
| Robot model | FANUC CRX-5iA collaborative robot |
| Structure | 6 axis articulated cobot arm, floor, wall or upside-down mounting |
| Payload capacity | 5 kg (driver, bit holder and vacuum cup included) |
| Working reach | 994 mm |
| Repeatability | +/- 0.03 mm (ISO 9283) |
| Robot mass | 25 kg |
| Motion range | J1 360 deg, J2 360 deg, J3 360 deg, J4 380 deg, J5 360 deg, J6 450 deg |
| Maximum speed | 1000 mm/s standard, 2000 mm/s in high speed mode |
| Allowable wrist moment | J4 15.4 Nm, J5 6.7 Nm, J6 4.0 Nm |
| Tightening capability | Screw driving torque up to 200 Nm (M16 class fastener) |
| Force sensing | Built-in force sensor on every axis, hand guidance enabled |
| Protection | IP67 body and wrist, IP67 driver spindle |
| Controller | R-30iB Plus with Dual Check Safety (DCS) software |
| Noise level | Below 70 dB |
| Operating temperature | 0 to 45 degC |
| Power supply | 220 V / 380 V, three phase, 50/60 Hz |
| Fixture | Two-position rotary table with model-specific locating nests |
| Quality documents | Torque calibration record, repeatability test report, functional test checklist |
Q: What exactly does this headlight screw tightening workstation include?
A: One FANUC CRX-5iA 6 axis cobot, the R-30iB Plus controller with safety software, a torque controlled screwdriver spindle, automatic screw feeding, the two-position rotary fixture with locating nests, guarding-free cell frame and the documentation set. Tooling for your specific lamp housing is quoted with the order.
Q: Why is a 5 kg payload enough for screwdriving?
A: A production driver with bit holder, feeder hose and a vision camera typically weighs 2 to 3.5 kg. The 5 kg payload leaves a safe margin, and the allowable wrist moments of 15.4 Nm at J4 and 6.7 Nm at J5 comfortably carry the offset load of a side-mounted driver.
Q: How accurate is the fastening position?
A: Repeatability is +/- 0.03 mm, so the driver returns to each programmed screw position within a few hundredths of a millimetre. Torque accuracy depends on the spindle you select, and each cell ships with a calibrated torque record.
Q: Can the cell run without a safety fence?
A: Yes. The cobot is certified to ISO 10218-1 and ISO/TS 15066, force sensing is standard and DCS software monitors restricted zones. A risk assessment of your layout is still required, and our engineers provide the cell layout drawing to support it.
Q: How is a new headlight model programmed?
A: An operator grips the arm, leads it to each fastening point, presses the record button on the flange and saves the sequence. Most variants are taught in under 30 minutes with no robot programming background.
Q: What protection does the workstation have for workshop conditions?
A: The arm body and wrist are IP67 rated, dust tight and resistant to coolant splash, and the operating range is 0 to 45 degC with noise below 70 dB.
Q: Do you provide installation and training?
A: Remote commissioning support is included. On-site installation, operator training and torque strategy development for your lamp design are available as optional services.