Quick Link
Quick Contact
Address
6 building,No 98, Fulian 1 road,Baoshan district, Shanghai, China.
Tel
86-021-80392549
Our Newsletter
Subscribe to our newsletter for discounts and more.
This vision-guided industrial robot arm for automotive seat installation is configured for trim line work, where a seat assembly must be lifted from a conveyor, aligned to four body studs and seated into the cabin without marking the leather or cross-threading a bolt. The arm carries the seat and its gripper on a 125 kg payload, so a front seat pair with rails, wiring and side airbag module moves as one unit.
Positioning on the trim line is never perfectly repeatable for automotive seat installation. Body-in-white hanger variation, stud weld tolerance and seat frame spring-back all shift the target by a few millimetres, which is why the cell pairs 3D vision with a force-compliant wrist. The camera locates the stud pattern on the body, the controller corrects the approach path, and the wrist, guided by FANUC iRVision 3D, absorbs residual offset so the rail slides onto the studs instead of being forced onto them, which is the difference between a clean vision-guided insertion and a rejected vehicle.
Reach of 3100 mm on the R-2000iC/125L lets one floor-mounted robot arm serve two body stations or cover the full cabin opening from a single pedestal, which keeps the pedestal out of the operator walkway. Repeatability of +/-0.05 mm holds the fastening pose stable across a shift, and torque-monitored fastening records each bolt against the vehicle identification number, so every automotive seat installation leaves a complete record.
For plants running several models on one line, seat variants are handled as stored programs and gripper jaw sets rather than hardware changes. A model recall loads the seat pose, gripper stroke and torque recipe for that variant, and the vision routine adapts to the new stud pattern without re-teaching point data.
| Category | Industrial Robot Arm | Robot Type | 6-Axis Articulated |
| Payload | 125 kg | Working Reach | 3100 mm |
| Repeatability | +/-0.05 mm | Protection | IP54/IP56 Body, IP67 Wrist |
| Mounting | Floor | Controller | R-30iB Plus |
| Seat Alignment | iRVision 3D plus Force Compliance | Voltage | 380 V / 400 V |
| Robot Weight | 1115 kg | Cycle Time | 45 s per Seat Pair |
| Warranty | 1 Year | Primary Application | Automotive Seat Installation |
Q: What is this vision-guided industrial robot arm designed to do?
A: It installs complete seat assemblies into vehicle bodies on a trim or final assembly line. The arm lifts the seat from the conveyor, aligns the rails to the body studs using 3D vision and force compliance, then fastens with a monitored torque recipe.
Q: Why does seat installation need vision and force compliance?
A: Body hanger variation and stud weld tolerance move the target by several millimetres between vehicles. Vision corrects the approach path and the compliant wrist absorbs the remaining offset, so the rail seats on the stud instead of being forced, which is where cross-threading and paint damage usually start.
Q: How much payload is available for the gripper and seat?
A: The R-2000iC/125L is rated at 125 kg, which covers a front seat pair with rails, wiring harness and side airbag module plus the gripper weight. Heavier seat configurations can be quoted on the R-2000iC/165F with 165 kg payload using the same cell layout.
Q: What cycle time can the cell reach?
A: A typical automotive seat installation cycle for a seat pair is about 45 seconds including pick, vision alignment, insertion and fastening, depending on cabin access and bolt count. The exact figure is confirmed from your line takt and gripper design.
Q: Is the seat installation record traceable?
A: Yes. Each fastening result from the vision-guided robot arm, including torque, angle and alignment offset, is written against the vehicle identification number, so quality can be reviewed per unit later.
Q: Which controller and interfaces are used?
A: The arm runs on the FANUC R-30iB Plus controller with standard fieldbus options, safety I/O and PLC handshaking, so the station integrates with existing line controllers and MES without a separate gateway.
Q: How is protection rated for a trim shop?
A: The arm body is rated IP54/IP56 and the wrist and J3 arm are IP67, which covers trim dust, adhesive overspray and routine wash-down. Additional covers or bellows are quoted for welding or paint shop positions.
Q: What are the commercial terms?
A: Minimum order quantity is 1 Set, priced from USD 70000 to 98000 per set depending on gripper, vision and fastening scope. Supply ability is about 20 Sets per month, delivery is 20 to 30 working days for a configured cell, and T/T or L/C is accepted with a 1 Year warranty.
Final scope is agreed from your body datum drawing, seat variant list, line takt and bolt torque specification. Gripper jaws, vision lighting, fastening spindle and safety fencing are specified per project, and a factory acceptance test runs on your sample body and seat before shipment.