Quick Link
Quick Contact
Address
6 building,No 98, Fulian 1 road,Baoshan district, Shanghai, China.
Tel
86-021-80392549
Our Newsletter
Subscribe to our newsletter for discounts and more.
This fenceless battery pack assembly robot arm with wiring inspection combines a six-axis collaborative arm, a dual-station fixture table, a servo screwdriver spindle and a vision inspection head into one commissioning-ready battery pack assembly cell. The station is laid out for lithium module and pack lines, so it places modules, seats busbars, drives retention screws and checks every connector before the pack moves to end-of-line electrical test.
Working envelope follows the 10 kg payload / 1249 mm reach class of the CRX-10iA collaborative arm, which gives the cell enough span to cover a full pack footprint from a single floor position. Repeatability of +/-0.04 mm holds screw positions and connector heights inside the tolerance band that battery pack assembly work actually needs, cycle after cycle, without touch-up programming.
Because the arm is force limited at the tool flange and stops on contact, the battery pack assembly robot arm runs beside operators without a safety fence. One side of the dual-station table stays open for manual module loading and rework while the robot assembles on the other, so a jam or a changeover never stops the line. A quick-change end effector moves the same arm from module placement to harness routing with no re-teaching of point data.
Wiring inspection happens in line rather than at a separate quality bench. The vision head photographs each connector block, confirms pin presence, terminal depth and latch engagement, then writes the verdict to the pack serial number. A rejected connector returns the pack to the operator with the exact fault location highlighted, so a missed latch or a pushed-back terminal is contained at the station instead of surfacing at high-voltage test.
| Category | Robotic Assembly Workstation | Robot Type | 6-Axis Collaborative |
| Payload | 10 kg | Working Reach | 1249 mm |
| Repeatability | +/-0.04 mm | Protection | IP40 |
| Mounting | Floor, Wall, Ceiling | Controller | R-30iB Mini Plus |
| Safety Standard | ISO 10218-1, ISO/TS 15066 | Voltage | 220 V / 380 V |
| Robot Weight | 40 kg | Station Footprint | 1800 x 1400 mm |
| Warranty | 1 Year | Primary Application | Battery Pack Assembly and Wiring Inspection |
Q: What is this fenceless battery pack assembly robot arm built for?
A: It is a single station for battery pack assembly and in-line wiring inspection. The arm places modules, seats busbars, drives screws and then verifies every connector, so one cell covers the assembly and the quality gate that follows it.
Q: Why is a fenceless cell possible here?
A: The collaborative arm is force limited and performs a safety-rated contact stop, so the cell is certified to ISO 10218-1 and ISO/TS 15066 for operation beside an operator. Risk assessment of your tooling and pack geometry stays part of the final acceptance.
Q: Which robot is the station built around?
A: The mechanical envelope follows the CRX-10iA class arm: 10 kg payload, 1249 mm reach, +/-0.04 mm repeatability, IP40 protection, 40 kg arm weight and an R-30iB Mini Plus controller. Alternative reach and payload classes can be quoted on the same frame.
Q: How does the wiring inspection actually work?
A: A vision head captures each connector block after insertion and checks pin presence, terminal depth and latch engagement. Results are written to the pack serial number, and a failed connector is flagged with its location so the operator sees the exact fault.
Q: Can it handle more than one pack size?
A: Yes. The dual-station table uses kinematic fixture plates, so a new pack variant is a plate change plus a stored program recall. Most changeovers finish in under fifteen minutes without touching robot point data.
Q: What torque control is available for screwdriving?
A: The spindle reports torque and angle per screw and can be paired with the arm force control to seat the screw and confirm the clamp load. Torque windows and trace records are set per fastening point.
Q: How is the cell installed and supported?
A: The station ships assembled, pre-wired and factory tested with a machinery test report, electrical drawings, safety documentation and a program backup. Remote commissioning support and on-site training are available; a 1 Year warranty covers the robot and station hardware.
Q: What are the order and delivery terms?
A: Minimum order quantity is 1 Set, priced from USD 28000 to 45000 per set depending on gripper, vision and fixture scope. Supply ability is about 30 Sets per month, with 15 to 25 working days for a configured station. T/T and L/C are accepted.
Final scope is agreed from your pack drawing, connector list and line cycle target. Gripper jaws, fixture plates, screwdriver bits, vision lighting and fieldbus mapping are specified per project, and a factory acceptance test runs on your sample pack before shipment.