Quick Link
Quick Contact
Address
6 building,No 98, Fulian 1 road,Baoshan district, Shanghai, China.
Tel
86-021-80392549
Our Newsletter
Subscribe to our newsletter for discounts and more.
The QC-510 is a 700 kg heavy duty tool changer with 4,860 Nm of static moment in X and Y and 3,500 Nm in Z. That combination is aimed at press tending and other cells where the end effector is both heavy and long, and where the tool changer sees a shock load every time a part is picked from a die.
Static X-Y moment of 4,860 Nm is roughly 48 percent above the 300 kg class, and that is the number that decides whether a 700 kg tool changer can hold a wide vacuum frame or a mechanical gripper at full reach. Z moment of 3,500 Nm covers the vertical load path during lift, transfer and set-down.
The QC-510 tool changer keeps the ATI media module architecture, so air, fluid, electrical signals, network communication and welding current all pass through the wrist on standard faces. Locked, unlocked and ready-to-lock sensors are integrated, and hardened locating pins carry the shear load so the locking mechanism is not the only thing holding a 700 kg tool in place.
| Model | QC-510 | Type | Heavy duty pneumatic tool changer |
| Suggested Payload Range | 700 kg | Static Locking Moment X-Y | 4,860 Nm |
| Static Locking Moment Z | 3,500 Nm | Lock Sensors | Locked / Unlocked / Ready-to-lock |
| Locating | Hardened pins | Media Modules | Air, fluid, electrical, network, welding current |
| Duty Class | Heavy duty, press tending shock loads | Series | ATI QC heavy duty series |
| Model | Suggested Payload | Static Moment X-Y | Static Moment Z |
| QC-210 | 300 kg | 2,710 Nm | 2,260 Nm |
| QC-310 | 510 kg | 3,290 Nm | 3,160 Nm |
| QC-510 | 700 kg | 4,860 Nm | 3,500 Nm |
| QC-835 | 300 kg | 2,700 Nm | 2,260 Nm |
| QC-850 | 700 kg | 3,500 Nm | 2,500 Nm |
| QC-1210 | 1,350 kg | 5,420 Nm | 5,420 Nm |
| QC-1310 | 2,990 kg | 11,000 Nm | 12,600 Nm |
Q1. What can the QC-510 tool changer carry?
700 kg suggested payload with 4,860 Nm static moment in X-Y and 3,500 Nm in Z. Because press tending adds shock, we size the tool changer against your cycle acceleration as well as the static load.
Q2. Why is the X-Y moment so much higher than Z?
Because handling tools are long. A wide vacuum frame or a long press gripper loads X-Y far more than Z, and the QC-510 tool changer is rated 4,860 Nm in X-Y against 3,500 Nm in Z to match that reality.
Q3. Can it survive press tending shock?
That is the design case. The heavy duty tool changer uses hardened locating pins as a separate shear path, and dynamic capacity sits above the published static ratings.
Q4. Does the tool changer report lock state?
Yes: locked, unlocked and ready-to-lock sensors are inside the unit, so the press cycle cannot start on an unconfirmed joint.
Q5. What media can pass through?
Air, fluid, electrical signals, network communication and welding current, using the standard ATI media modules that mount on the tool changer faces.
Q6. What is the next size up?
QC-1210 at 1,350 kg with 5,420 Nm in both directions, then QC-1310 at 2,990 kg. We move you up only when the moment data says the QC-510 tool changer is no longer the right size.