Quick Link
Quick Contact
Address
6 building,No 98, Fulian 1 road,Baoshan district, Shanghai, China.
Tel
86-021-80392549
Our Newsletter
Subscribe to our newsletter for discounts and more.
The QC-310 is the 510 kg step in the ATI heavy duty tool changer range, with 3,290 Nm of static moment in X and Y and 3,160 Nm in Z. It exists because payload alone does not describe a heavy handling job: a 500 kg gripper on a 1.2 m frame asks far more of a tool changer than the same mass held close to the flange, and the QC-310 is specified around that moment rather than around the payload figure.
This heavy duty tool changer keeps the X-Y and Z ratings close to each other (3,290 Nm and 3,160 Nm), which is what a handling cell with a swinging load needs. If one axis were far weaker, the tool changer would become the limiting component the moment the robot accelerates with a long tool.
The body carries the standard ATI media module faces, so the QC-310 tool changer can pass air, fluid, electrical signals, network communication and welding current through the wrist. Locked, unlocked and ready-to-lock sensors are integrated, so a 510 kg cell interlocks on the real state of the joint rather than on a valve timer.
| Model | QC-310 | Type | Heavy duty pneumatic tool changer |
| Suggested Payload Range | 510 kg | Static Locking Moment X-Y | 3,290 Nm |
| Static Locking Moment Z | 3,160 Nm | Lock Sensors | Locked / Unlocked / Ready-to-lock |
| Locating | Hardened pins | Media Modules | Air, fluid, electrical, network, welding current |
| Duty Class | Heavy duty, high inertia handling | Series | ATI QC heavy duty series |
| Model | Suggested Payload | Static Moment X-Y | Static Moment Z |
| QC-210 | 300 kg | 2,710 Nm | 2,260 Nm |
| QC-310 | 510 kg | 3,290 Nm | 3,160 Nm |
| QC-510 | 700 kg | 4,860 Nm | 3,500 Nm |
| QC-835 | 300 kg | 2,700 Nm | 2,260 Nm |
| QC-850 | 700 kg | 3,500 Nm | 2,500 Nm |
| QC-1210 | 1,350 kg | 5,420 Nm | 5,420 Nm |
| QC-1310 | 2,990 kg | 11,000 Nm | 12,600 Nm |
Q1. What can the QC-310 heavy duty tool changer carry?
510 kg suggested payload, with 3,290 Nm static moment in X-Y and 3,160 Nm in Z. We confirm the tool changer against your tool centre of gravity and acceleration before shipment.
Q2. When should I choose the QC-310 over the QC-210?
When the tool is heavier than roughly 300 kg, or when a long tool turns payload into moment. The QC-310 tool changer adds about 20 percent X-Y moment over the QC-210, which is the difference between margin and marginal.
Q3. Does the tool changer report its lock state?
Yes. Locked, unlocked and ready-to-lock sensors are integrated, so the robot controller reads the joint state directly instead of waiting on a timer.
Q4. Can it pass air and signals?
The QC-310 tool changer accepts the standard ATI media modules for air, fluid, electrical signals, network communication and welding current.
Q5. What if my payload grows again?
The next step is the 700 kg QC-510, then the 1,350 kg QC-1210. Because the interface logic is shared, moving up is a tool changer change rather than a cell redesign.
Q6. Are tool plates and stands available?
Yes. Tool plates, floating hangers, dust caps and bases belong to the same heavy duty range, and we quote the docking set with the tool changer.