Quick Link
Quick Contact
Address
6 building,No 98, Fulian 1 road,Baoshan district, Shanghai, China.
Tel
86-021-80392549
Our Newsletter
Subscribe to our newsletter for discounts and more.
The QC-110 is a pneumatic tool changer rated for 150 kg payloads, with a static locking moment of 784 Nm in X and Y and the same 784 Nm in Z. That balance between X-Y and Z is deliberate: a 150 kg tool changer on a welding workstation has to resist both the bending load of a long torch bracket and the vertical load of a heavy gripper, and the QC-110 is sized so neither direction becomes the weak point.
Locking is pneumatic and monitored. The tool changer carries locked, unlocked and ready-to-lock sensors inside the body, so the robot controller knows the state of the joint before the arm moves, rather than inferring it from a timer. On a welding workstation that interlock is what stops a torch from being dragged out of its plate with the coupling half open.
Hardened locating pins give the repeat positioning, and the body carries the standard ATI media module faces, so a 150 kg tool changer can pass air, fluid, electrical signals, network communication or welding current through the same interface. Eight 3/8 NPT air ports are built into the tool changer, which is enough for most dual-circuit welding and clamping setups without an external manifold.
| Model | QC-110 | Type | Pneumatic tool changer |
| Suggested Payload Range | 150 kg | Static Locking Moment X-Y | 784 Nm |
| Static Locking Moment Z | 784 Nm | Air Ports | 8 x 3/8 NPT |
| Lock Sensors | Locked / Unlocked / Ready-to-lock | Locating | Hardened pins |
| Media Modules | Air, fluid, electrical, network, welding current | Series | ATI QC standard series |
| Model | Suggested Payload | Static Moment X-Y | Static Moment Z | Air Ports |
| QC-7 | 16 kg | 20.3 Nm | 12.4 Nm | (5) M5 or #10-32 |
| QC-11 | 16 kg | 20.3 Nm | 12.4 Nm | (6) M5 or #10-32 |
| QC-20 | 25 kg | 56.5 Nm | 78 Nm | (12) M5 or #10-32 |
| QC-29 | 35 kg | 56.5 Nm | 78 Nm | (2) 1/8 NPT + (4) #10-32 |
| QC-40Q | 50 kg | 226 Nm | 226 Nm | (8) 1/8 NPT |
| QC-71 | 79 kg | 395 Nm | 395 Nm | (8) 1/4 NPT |
| QC-76 | 100 kg | 542 Nm | 701 Nm | (5) 3/8 NPT |
| QC-110 | 150 kg | 784 Nm | 784 Nm | (8) 3/8 NPT |
| QC-160 | 300 kg | 2,710 Nm | 2,260 Nm | (5) 3/8 NPT + (4) 1/2 NPT |
Q1. What payload does the QC-110 tool changer carry?
The suggested payload range is 150 kg, with 784 Nm static locking moment in X-Y and 784 Nm in Z. Dynamic ratings are higher than the published static values, and we confirm the duty cycle with you before shipment.
Q2. How do I know the tool changer is locked?
The unit contains locked, unlocked and ready-to-lock sensors, so the robot controller reads the joint state directly instead of relying on a time delay after the air valve opens.
Q3. Can it pass welding current?
Yes. The tool changer takes the standard ATI media modules, including welding current modules, so the high-current path runs through a rated interface rather than an external cable loop.
Q4. Why choose 150 kg instead of the 100 kg QC-76?
If your tool plus fixture sits above roughly 100 kg, or if the moment arm is long, the QC-76 becomes marginal. The QC-110 tool changer moves X-Y moment from 542 Nm to 784 Nm and adds a fourth 3/8 NPT air circuit.
Q5. What air pressure does the tool changer need?
Locking is pneumatic and driven from the robot air supply. We confirm the pressure and valve arrangement against your controller during order review, since the unlock circuit must be fail-safe.
Q6. Can the tool changer be serviced in the field?
Yes. The locking mechanism and the locating pins are accessible from the tool side, and the sensor states can be verified at the controller before any mechanical work starts.
Q7. Does it fit a standard robot flange?
The tool changer mounts on the robot flange pattern of the robot class it serves, and the tool plate repeats on hardened pins. Send us your flange drawing and we confirm the interface before shipment.