logo

RH56H1-E4 Dexterous Hand CAN FD EtherCAT 1kHz 12 Joints 6 DOF for Humanoid Robot

Place of Origin: China
Brand Name: INSPIRE-ROBOTS
Certification: CE
Model Number: RH56H1-E4R / RH56H1-E4L
Minimum Order Quantity: 1 Set
Price: 1800
Packaging Details: Foam-lined carton with shock indicator, one hand per carton
Delivery Time: 7-15 Working Days
Payment Terms: T/T
Supply Ability: 500 Sets per Month
Inquiry Now
Get A Quote
Specifications
Highlight Features

CAN FD EtherCAT Dual Bus Hand

,

1kHz Real-Time Robot Hand

,

6 DOF 12 Joints Humanoid Hand

Product Name / 产品名称:
RH56H1-E4 Dual Bus Dexterous Hand
Application / 应用场景:
CAN FD Production Lines, Machine Tending Cells, Dual-arm Platforms, Integrator Retrofits, Test Benches
Control Interface / 通信接口:
EtherCAT + CAN FD (both Active)
Communication Rate / 通信频率:
1 KHz
Quiescent Current / 静态电流:
193±10 MA (CAN FD) / 206±10 MA (EtherCAT) @24V
Peak Current / 峰值电流:
5 A @24V
Operating Voltage / 工作电压:
24-48 V DC
Degrees Of Freedom / 自由度:
6 DOF
Number Of Joints / 关节数:
12 Joints
Weight / 整手重量:
630±10 G (right Hand), 620±10 G (left Hand)
Repeatability / 重复定位精度:
±0.2 Mm
Passive Payload / 被动负载:
30 Kg
Product Description

Overview

  • • RH56H1-E4 is the CAN FD build of the RH56H1 five-finger dexterous hand, aimed at cells that already run a CAN FD network beside EtherCAT.
  • • Both buses stay active on the same unit, so a cell can command joints over EtherCAT while a secondary controller reads status over CAN FD.
  • • The hand runs a 1 kHz real-time loop on either bus, which keeps command latency identical whichever port the integrator chooses.
  • • Six degrees of freedom and twelve joints give the five fingers thumb opposition plus independent flexion on the remaining four.
  • • Weight is 630 g plus or minus 10 g for the right hand and 620 g plus or minus 10 g for the left, light enough for 3 kg class cobots.
  • • Width, circuit count and quiescent draw are published for both buses, so power budgets can be fixed before the hand arrives.
  • • Right and left builds are separate part numbers, ending in R and L, and each is stocked in four shell finishes.

Specifications

Parameter RH56H1-E4R
(Right Hand)
RH56H1-E4L
(Left Hand)
Unit
Control InterfaceEtherCAT + CAN FDEtherCAT + CAN FD-
Communication Rate11kHz
Quiescent Current (CAN FD)193 ± 10 @ 24 V193 ± 10 @ 24 VmA
Quiescent Current (EtherCAT)206 ± 10 @ 24 V206 ± 10 @ 24 VmA
Peak Current5 @ 24 V5 @ 24 VA
Operating Voltage24 – 4824 – 48V DC
Degrees of Freedom66DOF
Number of Joints1212pcs
Weight630 ± 10620 ± 10g
Repeatability± 0.2± 0.2mm
Fingertip Strength≥ 20≥ 20N
Thumb Fingertip Strength≥ 15≥ 15N
Force Resolution0.10.1N
Thumb Lateral Rotation60 – 18060 – 180°
Hand Closing Time< 0.8< 0.8s
Passive Payload3030kg
Sensing Channels2424pcs
  • • Bus load figures are measured at 24 V with the hand powered but idle, which is the number power designers actually need.
  • • The E2 variant keeps RS485 instead of CAN FD for cells on serial wiring, with the same mechanical build.

Advantages

Dual Bus Without a Gateway

  • • EtherCAT and CAN FD are both native on the hand, so no protocol bridge occupies cabinet space or adds latency.
  • • Joint commands, sensor values and error codes use one register map across both buses, so the integration code stays portable.
  • • A cell that later migrates from CAN FD to EtherCAT keeps the same end effector and the same fixtures.
  • • Only one cable entry is needed because both buses share the concealed internal harness.

Deterministic Timing

  • • The 1 kHz loop bounds jitter on command delivery, which matters when force thresholds must trigger inside a single cycle.
  • • A closing time under 0.8 s leaves margin for force ramping without eating into cell throughput.
  • • Repeatability of 0.2 mm and force resolution of 0.1 N keep behaviours reproducible between shifts.
  • • Twelve joints are reported individually, so trajectory checks can run at the controller instead of on the hand.

Electrical Fit

  • • The 24 to 48 V DC input matches standard cabinet supplies, with 5 A peak headroom for simultaneous joint moves.
  • • Quiescent draw of 193 mA on CAN FD or 206 mA on EtherCAT allows the hand to be powered from the arm tool flange.
  • • The all-metal skeleton and concealed wiring pass 20 stages of factory testing, including bus stability under long runs.

Applications

  • • Automotive component lines that already run CAN FD for sensors and tooling.
  • • Machine tending cells where the hand is swapped between CNC load and deburr stations.
  • • Dual-arm research platforms that need a documented bus with deterministic timing.
  • • Integrator retrofits where an RS485 hand is to be replaced without rewiring the cabinet.
  • • Packing and kitting lines that mix rigid parts with flexible pouches.
  • • Test benches that log joint and force data at 1 kHz for validation reports.
  • • Education labs teaching fieldbus integration on a five-finger end effector.

FAQ

Q1: Can EtherCAT and CAN FD be used at the same time?

Yes. Both ports can be active simultaneously, with EtherCAT normally used as the motion master and CAN FD carrying status or a secondary command stream.

Q2: What CAN FD bit rate is supported?

The hand communicates at a 1 kHz cycle over CAN FD with standard arbitration and data phase settings documented in the interface manual, so it drops into existing CAN FD networks without custom timing work.

Q3: Do I need a separate power supply for the hand?

Any 24 to 48 V DC source able to deliver 5 A peak is enough. Quiescent draw stays near 193 mA on CAN FD, so tool flange power is often sufficient.

Q4: Is the RS485 version mechanically identical?

Yes. The E2 series shares the housing, joints and finger geometry, and differs only in the secondary bus, so fixtures and mounting plates are interchangeable.

Q5: Can the hand run without any gripper-specific software?

The register map and trajectory commands work from any EtherCAT master or CAN FD node. Sample code and a Python wrapper are supplied, but no proprietary runtime is mandatory.

Related Products
Send An Inquiry