logo

CNGBS Builds Teach-Free Welding Workstation with Robot, Floor Track and Cantilever Boom for Overseas Client

2026-11-20

Latest company case about CNGBS Builds Teach-Free Welding Workstation with Robot, Floor Track and Cantilever Boom for Overseas Client

Case Study: A Complete Teach-Free Welding Workstation, From Robot Arm to Floor Track

When a fabrication customer moved from manual welding to automation, the requirement was not a single machine but a working cell that could be operated by welders rather than programmers. CNGBS supplied the complete package as one integrated teach-free welding workstation, combining a teach-free welding system, a CNGBS six-axis robot arm, and a floor track with cantilever boom. The customer's own team travelled to the factory for the pre-shipment review and ran the cell on sample parts.

The integrated teach-free welding workstation: robot arm on a floor track, welding torch and positioner set up for the customer's part family.
The integrated teach-free welding workstation: robot arm on a floor track, welding torch and positioner set up for the customer's part family.

The Problem: Welding Skill Is Getting Scarce, Batch Sizes Are Getting Smaller

The customer's production profile is typical of job shops: many part numbers, modest batch sizes, and long seams that must be repeated accurately. Manual welding depended on a small group of experienced welders, and every new part number on a conventional robot meant hours of teaching with a pendant before the first good weld.

The brief was simple to state and hard to deliver: a cell where the operator loads the part, presses start, and the machine finds the seam itself.

What CNGBS Delivered

The workstation was assembled from three subsystems, specified together so that they behave as one cell rather than three separate purchases:

  1. Teach-free welding system: laser vision seam tracking with automatic path generation. The sensor scans the joint before the arc starts, measures gap and mismatch, and writes the corrected path into the program, so no point-by-point teaching is required.
  2. CNGBS six-axis robot arm: the motion platform that carries the torch, the laser sensor and the wire feeder, with enough payload margin to run a water-cooled torch without derating the axes.
  3. Floor track with cantilever boom: the seventh axis that extends the working envelope along the workpiece and lets the arm reach over fixtures, so long structures can be welded without repositioning the part.
The customer's engineers and CNGBS technicians running the teach-free welding sequence on a sample part during the pre-shipment review.
The customer's engineers and CNGBS technicians running the teach-free welding sequence on a sample part during the pre-shipment review.

How the Workstation Runs

  1. Load and clamp: the operator positions the part on the fixture; no programming session is needed.
  2. Scan: the laser sensor sweeps the joint and reports actual position, gap and mismatch.
  3. Generate: the controller converts the scan into a weld path and stores it against the part number.
  4. Weld: the arm executes the path while closed-loop torch height control holds a constant stick-out.
  5. Repeat: the next identical part runs from the stored recipe, and a new part number starts again from step two.
Customer representatives and the CNGBS project team in front of the completed workstation.
Customer representatives and the CNGBS project team in front of the completed workstation.

Teach-Free Welding Package: Standard Specifications

The figures below describe the standard teach-free welding package used as the basis of this workstation. Project settings, fixture design and the customer's production data are covered by a confidentiality agreement and are not disclosed here.

Degrees of Freedom6 Axis plus trackRated Payload10~50 kg
Working Reach1000~2800 mmRepeatability±0.02 mm
Seam TrackingLaser vision, teach-freeWelding ProcessesMIG, MAG, TIG, plasma
Plate Thickness0.8~12 mmProtection RatingBody IP54, wrist IP67
Controller CompatibilityFANUC, KUKA, YASKAWA, ABBFieldbusEtherNet/IP, PROFINET, DeviceNet, I/O
Final mechanical and electrical checks on the track and cantilever assembly before packing.
Final mechanical and electrical checks on the track and cantilever assembly before packing.

Why a Track and Cantilever Boom Matters

A fixed robot covers a sphere. Real workpieces are often longer than that sphere in one direction. By mounting the arm on a floor track, the working envelope becomes a long corridor along the part instead of a bubble around a single station, and the cantilever boom lets the torch reach down into fixtures and over obstructions without moving the workpiece.

For the customer this meant one cell could handle part families that would otherwise need separate stations. It also keeps the floor clear for crane access and operator movement.

Results

  • No teach pendant sessions: new part numbers are production-ready in about fifteen minutes from a laser scan, instead of hours of point-by-point teaching.
  • Stable arc on thin sheet: ±0.02 mm repeatability with closed-loop height control keeps penetration consistent when stamped parts vary.
  • One cell, several part families: the track and boom extend the envelope so long workpieces can be welded without re-fixturing.
  • Existing controllers stay in service: the interface kit supports FANUC, KUKA, YASKAWA and ABB platforms, protecting capital already on the floor.
  • Operator-friendly: welders run the cell after a short training session, without needing robot programming experience.
The workstation prepared for export packing, with the customer's team present for the final handover.
The workstation prepared for export packing, with the customer's team present for the final handover.

Building a Similar Cell

Tell us the part family, the longest seam, plate thickness and your existing controller platform, and we will quote the complete teach-free welding workstation as one package.